How to Reset a Blink Camera: All Models (2026)

If you need to know how to reset a Blink camera, the correct method depends on which Blink model you own. Battery-powered cameras such as the Blink Outdoor 4 and Outdoor 2K+ usually need a simple power cycle rather than a factory reset, while Blink Mini cameras, video doorbells, the Wired Floodlight Camera and Sync Modules have their own reset procedures. Using the wrong method can create more setup work without fixing the original problem.

Blink Camera Reset Guide by Model

Blink uses the word reset for several different actions. Depending on the device, you may simply be restarting the hardware, placing it into setup mode or performing a deeper factory reset. Therefore, it helps to identify exactly what your camera needs before pressing a reset button.

How to Reset a Blink Camera: Start With a Power Cycle

A full reset should not be your first move simply because a Blink camera shows as offline. In many cases, a power cycle is enough to reconnect it without changing settings, deleting the camera or forcing you through setup again.

For a battery-powered Blink camera:

1. Remove the batteries from the camera.
2. Wait at least five seconds.
3. Reinstall the batteries with the polarity aligned correctly.
4. Give the camera time to reconnect.
5. Open the Blink app and try Live View.

If the batteries are old or you are already opening the compartment, this is also a good time to replace them. Blink specifies 1.5-volt non-rechargeable lithium AA cells for its battery cameras. I use Energizer Ultimate Lithium AA batteries, which match Blink’s recommended battery type.

For a full breakdown of battery counts and compatibility by model, see our guide to changing batteries in every Blink camera.

If several Blink cameras go offline at the same time, however, the cameras probably are not the problem. Instead, unplug the Sync Module for 30 seconds, reconnect it and give it time to come back online. A problem affecting an entire system is more likely to involve the Sync Module, Wi-Fi connection or internet service.

How to Reset Blink Outdoor 4 and Outdoor 2K+

The current Blink Outdoor cameras do not rely on a traditional factory-reset button as the first troubleshooting step. For both the Outdoor 4 and newer Outdoor 2K+, Blink recommends power cycling the camera when it appears offline.

1. Remove the camera from its mount if needed.
2. Open the rear battery compartment.
3. Remove both AA lithium batteries.
4. Wait five seconds.
5. Reinstall the batteries.
6. Close the battery compartment securely.
7. Wait for the camera to reconnect to the Sync Module.

If it still does not reconnect, check whether the Sync Module itself is online. Blink specifically recommends power cycling the Sync Module for 30 seconds as part of Outdoor 4 and Outdoor 2K+ troubleshooting.

I use the Blink Outdoor line, and this distinction saves a lot of unnecessary troubleshooting: if one camera has a problem, restart that camera first. If several cameras have the same problem, start with the Sync Module.

If you are replacing or expanding your setup, the Blink Outdoor 4 with Sync Module XR combines the camera with Blink’s current extended-range module.

For more hands-on details about the camera itself, see our Blink Outdoor 4 review.

How to Reset Blink Outdoor and Indoor 3rd Gen

The older Blink Outdoor and Indoor 3rd Gen cameras are still widely used. They also run on AA lithium batteries and can be restarted by removing power and reinstalling the batteries.

If one of these older cameras begins flashing red or drops offline:

1. Remove both AA batteries.
2. Inspect the batteries and contacts.
3. Reinstall a known-good pair of lithium batteries.
4. Wait for the camera to reconnect.
5. Check its status in the Blink app.

Blink’s current support documentation notes that Outdoor and Indoor 3rd Gen cameras repeatedly flash red when they have lost their internet connection. A fresh pair of batteries is also worth trying if you do not see the normal startup LED sequence.

The older XT and XT2 cameras behave similarly when power or connectivity is involved. Because these cameras are now legacy hardware, I would avoid deleting them from your Blink system unless basic power, battery and network troubleshooting has already failed.

How to Reset a Blink Mini, Mini 2 or Mini 2K+

Blink Mini cameras work differently because they remain connected to external power and have a physical reset button on the bottom of the camera.

Blink Mini

1. Leave the Mini plugged in and receiving power.
2. Locate the reset button on the bottom of the camera.
3. When a solid red light is showing and a reset is needed, press and hold the reset button for more than five seconds.
4. Release the button.
5. Wait for the blue LED to begin blinking slowly.

A slowly blinking blue light means the Mini is ready to be added to a Blink system.

Blink Mini 2

The Mini 2 uses almost the same process. However, its mount covers the reset button, so remove the mount before attempting the reset.

1. Keep the Mini 2 connected to power.
2. Remove the camera from its mount.
3. Locate the reset button on the bottom.
4. Press and hold the button for more than five seconds when a reset is required.
5. Wait for the blue LED to slowly blink.

If you need another Mini 2 for a Blink system or as a compatible indoor chime for some Blink doorbell installations, the Blink Mini 2 is the current model I would look at before the original Mini.

Blink Mini 2K+

The newer Mini 2K+ also has its reset button on the bottom. Blink’s current procedure is to press and hold that button for five seconds. After a reset, the camera needs to be set up again in the Blink app.

How to Reset a Blink Video Doorbell

Blink now has several generations of video doorbells, and their reset procedures are not identical. Check the model in the Blink app or on the hardware before following a reset procedure.

Blink Video Doorbell 1st Gen

For the original Blink Video Doorbell:

1. Remove the batteries for five seconds.
2. Reinstall the batteries.
3. Wait for the red LED to flash.
4. If needed, press the reset button on the back for five seconds.
5. The doorbell should then be ready to add to your Blink account.

If no red LED appears, Blink recommends trying fresh AA lithium batteries before moving on to more invasive troubleshooting.

Blink Video Doorbell 2nd Gen

The second-generation Blink Video Doorbell uses three AA lithium batteries. If it goes offline or will not enter setup correctly:

1. Remove all three batteries.
2. Wait five seconds.
3. Reinstall the batteries.
4. Watch for the red LED.

Unlike the first-generation model, Blink’s current troubleshooting instructions do not require the additional five-second reset-button step for the second-generation doorbell.

For hands-on details about the current model, see our Blink Video Doorbell review.

Battery Doorbell 2K+ and Wired Doorbell 2K+

The newer 2K+ doorbells use a more conventional physical reset system. Both models have a reset button on the back.

• Short press: Power cycles the doorbell.
• Long press: Returns the doorbell to its factory firmware.

These models can also be factory reset through the Blink app. A true factory reset is much more destructive than an ordinary restart because Blink says it restores the device to its original factory settings and removes stored content.

As a result, use the short power-cycle reset first unless you specifically need to factory reset the doorbell.

How to Reset a Blink Wired Floodlight Camera

The Blink Wired Floodlight Camera has a reset button on top of the camera body. Because of its location, the button may be difficult to see once the floodlight is installed.

• Short press of less than five seconds: Resets the camera and resolves many setup issues without erasing the Wi-Fi configuration.
• Long press: Places the camera into setup mode and erases its stored Wi-Fi credentials.

If the camera simply stopped responding, start with the short press. There is no reason to erase the Wi-Fi configuration unless the camera needs to connect to another network or normal troubleshooting has failed.

For more on the hardware itself, see our Blink Wired Floodlight Camera review.

How to Reset a Blink Sync Module

If you searched for reset Blink Sync Module, first decide whether the module needs a reset or merely a restart.

Start with the less disruptive option:

1. Unplug the Sync Module from power.
2. Wait 30 seconds.
3. Plug it back in.
4. Wait for it to reconnect to Wi-Fi.
5. Check whether your cameras return online.

Blink recommends going through normal troubleshooting before using the Sync Module’s physical reset button. If the problem continues, the Sync Module Core, Sync Module 2 and Sync Module XR use essentially the same reset procedure.

1. Leave the Sync Module connected to power.
2. Locate the reset button on the back.
3. Press and hold the reset button.
4. Continue holding until the LED turns solid red.
5. Release the button.
6. Wait for a blinking blue LED and solid green LED.

That blinking-blue and solid-green combination means the Sync Module is in pairing mode and ready for setup.

If you want local storage and newer extended-range support, the Blink Sync Module XR is the newer option. The Sync Module 2 remains useful for systems using USB flash-drive local storage.

Sync Module 1st Gen

The first-generation Sync Module is slightly different. Its recessed reset button is on the side near the USB port. Use a small, thin object such as a paperclip to press the button until you feel it click. When the LEDs change to blinking blue and solid green, it is ready for setup.

Before resetting any Sync Module because cameras have weak connectivity, check where the module is located. Our Blink Sync Module placement guide explains how the module needs a reliable connection both to your router and to the cameras it serves.

Resetting a Blink Camera After Changing Wi-Fi

A new router, Wi-Fi name or Wi-Fi password does not necessarily mean you need to delete every Blink camera and start over.

Battery-powered models such as the Outdoor 4 and Outdoor 2K+ communicate through their Sync Module. Therefore, if your home Wi-Fi changes, update the Sync Module’s Wi-Fi connection rather than trying to reconfigure every dependent camera individually.

Blink specifically notes that changing the Wi-Fi network on a Sync Module does not delete previously saved clips.

Standalone Wi-Fi devices such as Blink Mini cameras and the Wired Floodlight Camera can have their network connection updated through the Blink app.

Blink equipment still relies heavily on 2.4 GHz Wi-Fi. If setup repeatedly fails after a reset, especially with a mesh system or router that combines 2.4 and 5 GHz under one network name, see our guide to connecting a 2.4 GHz smart-home device to Wi-Fi.

What to Do If Your Blink Camera Still Will Not Connect

If you followed the correct instructions for how to reset a Blink camera and the device still will not connect, work through the rest of the system before deleting anything.

1. Check the Sync Module. If several cameras are offline, start there rather than resetting each camera individually.
2. Check the batteries. Weak batteries can cause setup and connectivity problems even if the camera worked normally before.
3. Restart the router. Unplug it for about 30 seconds, reconnect it and allow the network to come fully back online.
4. Check signal strength. Blink systems depend on both the camera-to-Sync-Module connection and the Sync-Module-to-router connection.
5. Verify the Wi-Fi password. This is especially important after changing a router or network settings.
6. Move the hardware temporarily. During setup, bring the camera and Sync Module closer together to eliminate signal strength as the cause.
7. Check whether the system is armed. A camera that connects correctly but does not record motion may simply have motion detection disabled or belong to a disarmed system.
8. Delete and re-add the device only as a last resort. A temporary network problem generally does not justify rebuilding the camera configuration.

If you have a large Blink system, resetting the Sync Module too early can make diagnosis harder. First determine whether the issue affects one camera, several cameras, the Sync Module or the entire network.

Frequently Asked Questions

Where is the reset button on a Blink camera?

Blink Mini cameras have a reset button on the bottom. The original Video Doorbell and newer 2K+ doorbells have reset controls on the back. The Wired Floodlight Camera has a reset button on top. Current Outdoor battery cameras are normally restarted by removing the batteries rather than by using a factory-reset button.

How do I factory reset a Blink camera?

There is no single factory-reset procedure for every Blink camera. Outdoor models normally begin with a battery power cycle, while Mini cameras use their reset button to enter setup mode. Newer Battery Doorbell 2K+ and Wired Doorbell 2K+ models support a deeper factory reset. Follow the instructions for your exact model rather than using a generic reset sequence.

Will resetting a Blink camera delete my recordings?

A normal power cycle or standard reset does not automatically erase cloud recordings. Blink also states that changing a Sync Module’s Wi-Fi network does not delete saved clips. A true factory reset on the newer 2K+ doorbells is different because it restores factory settings and removes stored content.

Should I reset the camera or the Sync Module?

If one battery camera is malfunctioning, restart that camera first. If several cameras go offline together, check and power cycle the Sync Module. A physical Sync Module reset should come after basic troubleshooting rather than before it.

Why is my Blink camera blinking red after a reset?

A red LED generally indicates that a Blink camera is disconnected, in setup mode or trying to establish a connection, depending on the model. On Outdoor and Indoor 3rd Gen cameras, repeated red flashes can indicate a lost connection. On Mini cameras, a solid red light usually indicates that the camera is not connected to the internet.

Can I reset a Blink camera without deleting it from my account?

Yes. A normal power cycle or supported reset procedure does not usually require deleting the camera from your Blink account. Blink specifically states that resetting Mini and Mini 2 cameras does not remove them from the system or account. Deleting and re-adding a device should generally be reserved for cases where normal troubleshooting fails.

For more help with Blink cameras, visit our Blink Camera Reviews and Guides, learn where to position a Blink Sync Module, or read our complete Blink subscription and local storage guide.